This guide sets out a practical bleeding sequence that works on most generator engines, mechanical and electronic, and explains how to find the leak that keeps letting air back in. Always follow the engine manual where it differs, because some fuel systems have specific bleed points or self-bleeding features.
How air gets into the fuel system
The most common cause is simply running the tank dry, which pulls air through the entire supply side. Other causes include filter changes without priming, work on fuel lines or the injection pump, a day tank transfer pump failure, and slow suction-side leaks at fittings, filter seals or cracked lines. Suction-side leaks are sneaky: fuel does not drip out, air is drawn in instead.
Low fuel in a tank can also let the pickup draw air when the set is on a slope or when fuel sloshes, which is a known issue on trailer and skid sets moved between sites.
Safety before you open anything
Fuel under pressure and hot surfaces are a dangerous combination. Work with the engine cold where possible, keep ignition sources away, have spill kits and absorbent material ready and a suitable extinguisher at hand. Never loosen high pressure lines on a running engine to bleed them on a common rail system; the pressure is high enough to inject fuel through skin. Isolate the set from automatic start before working on it, as described in our guide to field technician safety.
Collect bled fuel in a container rather than letting it run onto the baseframe or into the ground, and clean up fully before any test run.
Bring the right kit for the job: spare filters and seals for the engine model, a clean fuel container, rags, a clear length of fuel hose to watch for bubbles, a vacuum and pressure gauge for the supply side, and a charged jump pack or spare battery. Bleeding often needs more cranking than a tired starting battery can give.
The bleeding sequence
- Restore fuel. Fill the tank or day tank and confirm the supply valve is open and the transfer system is working. Check for water and dirt before refilling a run-dry engine, since the last fuel drawn often carries sediment.
- Fill the filters. Where the design allows, fill new filter housings with clean fuel. Prime the primary filter or water separator first using its hand pump or the electric lift pump.
- Bleed the low pressure side. Open the bleed screw on the secondary filter head and operate the priming pump until fuel flows without bubbles, then close the screw.
- Bleed the injection pump. On mechanical pumps, open the pump bleed point and prime until clear fuel appears. On many electronic systems, cycling the ignition several times runs the electric lift pump and purges the low pressure side automatically.
- High pressure side. On mechanical systems, crack injector line nuts at the injectors one or two at a time while cranking briefly, until fuel appears, then tighten. On common rail systems, follow the manual; most purge the rail on cranking once the low pressure side is full.
- Start. Crank in short bursts with rests to protect the starter and batteries. Once the engine fires, let it run at idle or rated speed with no load until it settles.
When the engine starts then stalls
If the engine runs for a short time and then stalls or begins to hunt, air is still entering. Watch a clear section of line or a sight glass for bubbles. Check every joint on the suction side, the filter bowl seals, the lift pump diaphragm on mechanical pumps, and the return line arrangement. A partially blocked tank vent can also cause a vacuum that starves the pump.
Hunting caused by air in the fuel can look a lot like a governor problem. Our page on diagnosing hunting and surging explains how to separate fuel supply faults from control faults. If the engine still refuses to start once fuel is confirmed, work through the wider checks in our generator troubleshooting guide.
Test run and record
Once the engine runs steadily, apply load in steps if a load bank or site load is available, and watch for misfire, smoke or speed dips that suggest remaining air. Check every disturbed joint for leaks under pressure. Inspect the filters again after the run.
Record the cause of the air ingress, what was replaced or tightened, the fuel condition and the test result. Most importantly, fix the reason the set ran dry: a failed float switch, a transfer pump fault, a missing refuelling schedule or a fuel level alarm that was not wired to anyone’s phone. Those causes come up again and again in routine preventive maintenance visits.
Preventing the next call-out
Fuel level monitoring with alarms, regular checks of transfer pumps and float switches, filter changes done with proper priming, and periodic testing of fuel quality prevent most bleeding call-outs. For sites without full-time staff, remote monitoring of fuel level and engine status lets the service team act before the tank empties.
Where a fleet of sets keeps suffering the same faults, a structured service programme is usually cheaper than repeated emergency visits. USP&E provides that through its generator operations and maintenance service, covering fuel systems, controls and testing.
About the authors
This guide comes from the USP&E field technicians who restore and maintain diesel generator sets at remote mines, telecom sites, standby installations and temporary power sites. USP&E is an EPC and O&M contractor, not a broker, with 150+ power projects in 45+ countries, 25,000 MW contracted since 2002 and 24+ years in the field. Sets with worn fuel systems can be rebuilt under our refurbishment scope.
Offices: Colorado Springs (1755 Telstar Dr, Suite 300), Knoxville (800 S Gay St, Suite 700), London (162-168 Regent Street), Johannesburg (22 Kildoon Rd, Bryanston), Cape Town (31 Brickfield Road, Woodstock) and China (No. 1 Ningzhou Road, Wuxi). Regions: USA | AFRICA | UK | UAE | CHINA. ISO 9001 and ISO 45001 certified.
Fuel bleeding questions
How do you bleed air from a diesel generator fuel system?
Restore fuel, prime the filters, bleed the low pressure side at the filter head, bleed the injection pump, then purge the high pressure side by cranking or cracking injector lines as the manual allows.
Why will my generator not start after running out of fuel?
Running dry pulls air into the filters, pump and lines. The system must be bled before the engine can build injection pressure.
Can I bleed a common rail engine by loosening injector lines?
Not while it runs. Common rail pressure is dangerous. Follow the manual, which usually relies on the lift pump and cranking to purge the rail.
Why does the engine start and then stall?
Air is usually still entering through a suction-side leak, filter seal, lift pump fault or blocked tank vent.
Do new fuel filters need priming?
Yes. Filling or priming new filters before starting prevents a large slug of air reaching the injection pump.
How can I stop a generator running out of fuel again?
Use fuel level alarms, check transfer pumps and float switches, and set a refuelling schedule linked to monitoring.
Call out a field technician
Tell us the set, what happened before it stopped and what you see now, and a USP&E field technician will plan the visit.
Phone +27 10 822 2324 during office hours, or write to info@uspeglobal.com at any time; the field service contact form also routes straight to our project engineers. If a set needs replacing, see our available diesel generators.
